Antenna effect

Figure 1: Illustration of the cause of antenna effect. M1 and M2 are the first two metal interconnect layers.

The antenna effect, more formally plasma induced gate oxide damage, is an effect that can potentially cause yield and reliability problems during the manufacture of MOS integrated circuits.[1][2][3][4][5] Fabs normally supply antenna rules, which are rules that must be obeyed to avoid this problem. A violation of such rules is called an antenna violation. The word antenna is something of a misnomer in this contextthe problem is really the collection of charge, not the normal meaning of antenna, which is a device for converting electromagnetic fields to/from electrical currents. Occasionally the phrase antenna effect is used in this context,[6] but this is less common since there are many effects,[7] and the phrase does not make clear which is meant.

Figure 1(a) shows a side view of a typical net in an integrated circuit. Each net will include at least one driver, which must contain a source or drain diffusion (in newer technology implantation is used), and at least one receiver, which will consist of a gate electrode over a thin gate dielectric (see Figure 2 for a detailed view of a MOS transistor). Since the gate dielectric is so thin, only a few molecules thick, a big worry is breakdown of this layer. This can happen if the net somehow acquires a voltage somewhat higher than the normal operating voltage of the chip. (Historically, the gate dielectric has been silicon dioxide, so most of the literature refers to gate oxide damage or gate oxide breakdown. As of 2007, some manufacturers are replacing this oxide with various high-κ dielectric materials which may or may not be oxides, but the effect is still the same.)

Figure 2. Diagram of a MOSFET, showing source/drain implant and gate dielectric.

Once the chip is fabricated, this cannot happen, since every net has at least some source/drain implant connected to it. The source/drain implant forms a diode, which breaks down at a lower voltage than the oxide (either forward diode conduction, or reverse breakdown), and does so non-destructively. This protects the gate oxide.

However, during the construction of the chip, the oxide may not be protected by a diode. This is shown in figure 1(b), which is the situation while metal 1 is being etched. Since metal 2 is not built yet, there is no diode connected to the gate oxide. So if a charge is added in any way to the metal 1 shape (as shown by the lightning bolt) it can rise to the level of breaking down the gate oxide. In particular, reactive-ion etching of the first metal layer can result in exactly the situation shown - the metal on each net is disconnected from the initial global metal layer, and the plasma etching is still adding charges to each piece of metal.

Leaky gate oxides, although bad for power dissipation, are good for avoiding damage from the antenna effect. A leaky oxide can prevent a charge from building up to the point of causing oxide breakdown. This leads to the somewhat surprising observation that a very thin gate oxide is less likely to be damaged than a thick gate oxide, because as the oxide grows thinner, the leakage goes up exponentially, but the breakdown voltage shrinks only linearly.

Antenna rules

Antenna rules are normally expressed as an allowable ratio of metal area to gate area. There is one such ratio for each interconnect layer. The area that is counted may be more than one polygon it is the total area of all metal connected to gates without being connected to a source/drain implant.

Fixes for antenna violations

Figure 3: Illustration of three possible fixes to an antenna violation.

In general, antenna violations must be fixed by the router. Possible fixes include:

References

  1. T. Watanabe, Y. Yoshida, “Dielectric Breakdown of Gate Insulator due to Reactive Etching, ” Solid State Technology, Vol. 26 (4) p. 263, Apr. 1984
  2. H. Shin, C. C. King, C. Hu, “Thin Oxide Damage by Plasma Etching and Ashing Processes, ” Proc. IEEE Int’l Reliability Phys. Symp., p. 37, 1992
  3. S. Fang, J. McVittie, “Thin-Oxide Damage from Gate Charging During Plasma Processing, ” IEEE Electron Devices Lett. Vol. 13 (5), p. 288, May 1992
  4. C. Gabriel, J. McVittie, “How Plasma Etching Damages Thin Gate Oxides,“ Solid State Technol. Vol. 34 (6)p. 81, June 1992.
  5. Hyungcheol Shin, Neeta ha, Xue-Yu Qian, Graham W. Hills, Chenming Hu, “Plasma Etching Charge-Up Damage to Thin Oxides, ’’ Solid State Technology, p. 29, Aug. 1993
  6. Sibille, A.; 2005, A framework for analysis of antenna effects in UWB communications, IEEE 61st Vehicular Technology Conference, Volume 1, 30 May-1 June 2005, pp. 48 - 52
  7. From the above reference: Several major antenna effects are considered, like impedance matching, antenna gain, frequency-dependent radiation patterns, and antenna temporal dispersion in the presence of the radio channel.
This article is issued from Wikipedia - version of the 11/29/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.